产品中心
B系列
| 介绍： | DescriptionThe B1, B2, and B3sensors are capacitiv |
|---|
Description
The B1, B2, and B3 sensors are capacitive spring mass accelerometers with integrated sensor electronics. Requiring very low power consumption these are characterized by a high degree of long-term stability. Resonant peaks are minimised by means of a special gas-dynamic damping in the primary transformer.
Manufactured with an Analog DC output, the integrated sensor electronics require only minimal power and are in conjunction with the capacitive primary transformer characterized by high accuracy, linearity, and long-term stability.
Applications
The B Series are used for applications requiring high overload tolerance, high long-term stability, small lower cut-off frequency down to measurement of static acceleration, very short on-transition delay and low power consumption.
Typical applications include:
measurements on vehicles, machinery, buildings, and plants for process control and error diagnosis
seismic measurements
inclination measurements (i.e. ±90º)
safety engineering
dynamic measurement of position & velocity
Features
Compact housing, less than 1” diameter
Very high overload resistance
Insensitive to interference by magnetic and electric fields
Lower cut-off frequency is zero, hence suitable for measuring static acceleration, such as gravity (inclinations) or radial acceleration (centrifugal force)
Linear frequency response with little or no resonant peak at upper cut-off frequency
Low non-linearity
High signal-to-noise ratio
No measurable hysteresis of signal
Hermetically sealed
High long-term stability
Small temperature drift
Integrated sensor electronics
Analog DC or pulse width modulated or frequency modulated output
Low power consumption
Very short settling time Multiple housing options
MECHANICAL CHARACTERISTICS | |||||||||||
Housing | Nickel Plated Brass | ||||||||||
Protection Degree | IP65 | ||||||||||
Mounting | M4 Mounting Stud, M3 optional | ||||||||||
Mounting Plane | See “Figure 1” | ||||||||||
Outline Dimensions | Ø 0.945” (Ø 24mm) X .434” (11mm) h | ||||||||||
Electrical | Standard | 3 highly flexible, color-coded wires Ø 0.04” (Ø 1.0mm) x 7.0” (18cm) | |||||||||
A: Shielded cable Ø 0.083” (Ø 2.1mm) x 1.65’ (0.5m) | |||||||||||
Connection | Optional | ||||||||||
B: 3 highly flexible, single color wires with Teflon isolation for extended temperature range | |||||||||||
Weight | Approx. 0.89 ounces (25 grams) (not including cable) | ||||||||||
Operating Temperature | -40°F to +185°F | (-40° to +85°C ), optional +257ºF (+125ºC) | |||||||||
Storage temperature | -49°F to +194°F | (-45° to +90°C ), optional +257ºF (+125ºC) | |||||||||
TYPE | B1 | B2 | B3 | |||
Measuring Range | ±3g (Approx. ±30m/s2) | ±10g (Approx. ±100m/s2) | ±50g (Approx. ±500m/s2) | |||
Resolution | <.001g | <.005g | <.020g | |||
Frequency Range | 0…160Hz | 0…350Hz | 0…550Hz | |||
Max. Non-linearity | <0.5% | |||||
Cross Axis Sensitivity | <1% | |||||
Mechanical Overloading in | 10,000g (Approx. 100,000m/s2) | |||||
Measuring Direction | ||||||
Power Supply UbN (Regulated) | 5 Volt | |||||
Min ... Max. Supply Ubz | 3 ... 6 Volt | |||||
Current Consumption Ub=5Volt | Approx. 1mA | |||||
ANALOG VOLTAGE OUTPUT MODEL AT UBN=5VOLT | ||||||
Sensitivity | Approx. 110mV/g | Approx. 23mV/g | Approx. 6.5mV/g | |||
Temperature Drift of Sensitivity | < +0.06%/°C | |||||
Temperature Drift of Zero | < 0.1mV/°C | |||||
Zero Offset at Ub=5V | 2.5 ±0.1 Volt - generally: 0.5Ub ±4% | |||||
Output Impedance | 10kΩ | |||||
Digital pulse-width modulated output signal - linear to the degree of angle - available upon request.
CABLE WIRING TABLE:
3-WIRE (standard) | SHIELDED CABLE (optional) | ||
RED | +5VDC Stable | RED | +5VDC Stable |
WHITE | Output Signal | BLUE | Output Signal |
BLUE | GND (housing) | SHIELD | GND (housing) |
ATTENTION! The supply voltage must not exceed 6 Volt and the polarity must not be reverse
北京优利威科技有限公司专业提供各种传感器技术解决方案
如有产品需求或技术咨询，请拨打客服电话：010-51294688
或关注优利威官方微信公众号：优利威
